免費論壇 繁體 | 簡體
Sclub交友聊天~加入聊天室當版主
分享
返回列表 發帖

[日蝕引擎] 請問3G…3.0的原廠缸壓壓力值!!

請問有高手知道3G~3.0的缸壓壓力~原廠是設定在多少?我沒有維修手冊~網路上也查沒有數據!!
因為最近感覺車的吹漏氣好像變大了!!
想說先測量看看缸壓正不正常?
可是沒有原廠缸壓數據!!

我猜大概在12bar

TOP

三代原廠維修手冊-以下先參考!!!


2000-2002 Mitsubishi Eclipse Factory Service Manual
http://tearstone.com/2000-2002-eclipse-service-manual/

2003-2005 Mitsubishi Eclipse Factory Service Manual
http://tearstone.com/2003-2005-eclipse-factory-service-manual/

00-02:
http://tearstone.com/eclipsefsm/54A.PDF
http://tearstone.com/eclipsefsm/54B.PDF

03-05:
http://tearstone.com/eclipsefsm/GR00008000-54.pdf
http://tearstone.com/eclipsefsm/GR00008200-54B.pdf




請問有高手知道3G~3.0的缸壓壓力~原廠是設定在多少?我沒有維修手冊~網路上也查沒有數據!!
因為最近感 ...
if797 發表於 2015-11-21 01:52

TOP

剛剛睡飽了幫你找出來手冊說明位置..........
你參考參考,翻譯也是參考,以原文為主
測試步驟請做足歐,別漏了!!!!!!

這是00年-02年 三代 你的是幾年分?????

一、說明出處
2000-2002年 三代
http://tearstone.com/2000-2002-eclipse-service-manual/
的這一篇 的第八頁 下半 跟 第九頁 上半
Group 11C – Engine Mechanical 3.0L
http://tearstone.com/eclipsefsm/11C.PDF

二、說明內容
未命名.jpg
2015-11-21 20:18

2.jpg
2015-11-21 19:59


三、說明原文-以原文為主
COMPRESSION PRESSURE CHECK

1. Before inspection, check that the engine oil, starter and
battery are normal. Also, set the vehicle in the following
condition:
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights, and all accessories: OFF
• Transaxle: Neutral (P range on vehicles with A/T)
2. Disconnect the spark plug cables.
3. Remove all of the spark plugs.
4. Disconnect the crankshaft position sensor connector.
NOTE: Doing this will prevent the engine control module
from carrying out ignition and fuel injection.

Keep your distance from the spark plug hole when
cranking. Oil, fuel, etc., may spray out from the spark
plug hole and may cause serious injury.
5. Cover the spark plug hole with a shop towel etc., during
cranking. After the engine has been cranked, check for
foreign material adhering to the shop towel.
6. Set compression gauge to one of the spark plug holes.
7. Crank the engine with the throttle valve fully open and
measure the compression pressure.
Standard value (at engine speed of 250 − 400 r/min):
824 kPa (119 psi)
Minimum limit (at engine speed of 250 − 400 r/min):
575 kPa (83 psi)
8. Measure the compression pressure for all the cylinders, and
check that the pressure differences of the cylinders are
below the limit.
Limit: 98 kPa (14 psi)
9. If there is a cylinder with compression or a compression
difference that is outside the limit, pour a small amount of
engine oil through the spark plug hole, and repeat the
operations in steps 6 to 8.
(1) If the compression increases after oil is added, the cause
of the malfunction is a worn or damaged piston ring and/
or cylinder inner surface.
(2) If the compression does not rise after oil is added, the
cause is a burnt or defective valve seat, or pressure is
leaking from the gasket.
10.Connect the crankshaft position sensor connector.
11.Install the spark plugs and spark plug cables.
12.Use the scan tool to erase the diagnostic trouble codes.
NOTE: This will erase the diagnostic trouble code resulting
from the distributor connector being disconnected.

四、說明翻譯-僅供參考
壓縮壓力檢查

1.檢查前,檢查機油,起動機和
電池是正常的。另外,在下面設定的車輛的
條件:
•發動機冷卻液溫度:80 - 95°C(176 - 203°F)
•燈光,和所有附件:OFF
•驅動橋:中性(車輛用A / T P檔位)
2.拔下火花塞電纜。
3.刪除所有火花塞。
4.斷開曲軸位置傳感器連接器。
注:否則可能會導致發動機控制模塊
從進行點火和燃料噴射。

請從火花塞孔,當你的距離
起動。石油,燃料等,可從火花噴了出來
堵塞漏洞,可能導致嚴重的人身傷害。
5.蓋上鋪巾等,在火花塞孔
起動。後發動機已經拍成,檢查
異物附著在鋪巾。
6.設置壓縮軌距向火花塞孔中的一個。
7.曲柄與節氣門全開並且發動機
測量壓縮壓力。
標準值(250發動機轉速 - 400轉/分):
824千帕(119磅)
最小限制(以250發動機轉速 - 400轉/分):
575千帕(83磅)
8.測量所有氣缸的壓縮壓力,以及
檢查氣缸的壓力差別
低於限制。
限制:98千帕(14磅)
9.如果有一個與壓縮或壓縮的氣缸
不同之處在於超出了限制,倒入少量
機油通過火花塞孔,並重複
操作步驟6至8。
(1)如果油壓縮後的增加添加,病因
故障是磨損或損壞活塞環和/
或氣缸的內表面。
(2)如果壓縮油後不漲添加時,
原因是燒焦的或有缺陷的氣門座,或壓力
從墊片洩漏。
10.Connect曲軸位置傳感器連接器。
11.Install火花塞和火花塞電纜。
12.Use掃描工具來清除故障碼。
注意:這將清除診斷故障碼產生
從分配器連接器被斷開。

請問有高手知道3G~3.0的缸壓壓力~原廠是設定在多少?我沒有維修手冊~網路上也查沒有數據!!
因為最近感 ...
if797 發表於 2015-11-21 01:52

TOP

整理出來嚕,自己去看看吧,有分年份!!!!

日蝕3代3.0原廠汽缸壓力值及缸壓標準測試流程。

TOP

感謝賓仔大..以服用..我的是2000年GT!!

TOP

返回列表